The Kenmore Power Miser 9 is a great energy saving appliance, but there is one common problem that can occur. The pilot light may go out frequently. This can be frustrating, but there are some things you can do to fix the problem.
If your Kenmore Power Miser 9 pilot light keeps going out, there are a few possible reasons. First, make sure that the gas valve is turned on all the way. If it is, then the next thing to check is the thermocouple.
The thermocouple is a safety device that turns off the gas if the pilot light goes out. If the thermocouple is defective, it will need to be replaced. Another possibility is that there is something blocking the airflow to the pilot light.
This could be dirt or debris in the burner assembly or a problem with the venturi tube. Cleaning or replacing these parts should fix the problem.
Kenmore Power Miser 9 Water Heater Pilot Keeps Going Out- General Information…
What Does It Mean If the Pilot Light Keeps Going Out?
If your pilot light keeps going out, it could be a sign that your gas line is not properly sealed. A small leak in the gas line can cause the pilot light to go out because there is not enough gas getting to the burner. If you think you might have a gas leak, it’s important to call a professional to come and check it out.
Why Does My Pilot on My Water Heater Keep Going Out?
If your pilot light on your water heater keeps going out, there are a few possible causes. One possibility is that the thermocouple, which is responsible for sensing whether or not the pilot flame is lit, may be damaged or defective. Another possibility is that there is a draft in the room where the water heater is located, which can cause the pilot light to go out.
Finally, it’s also possible that the gas supply to the water heater is shut off or interrupted in some way. If you’re unsure of what’s causing your pilot light to keep going out, it’s best to contact a qualified technician for diagnosis and repair.
How Do You Fix a Pilot Light That Won’T Stay Lit?
If your pilot light won’t stay lit, there are a few possible causes. The first thing you should check is the gas supply to the pilot light. If the pilot light is not getting enough gas, it will go out.
Another possibility is that the pilot light flame is too low. The flame should be about 1/2 inch high. If it’s lower than that, adjust the flame height by turning the screw next to the pilot light.
Finally, make sure that there is no draft in the area where the pilot light is located. A draft can cause the flame to go out.
Why Does My Pilot Light Keep Going Out After Replacing Thermocouple?
If your thermocouple is new and you’re still having issues with your pilot light going out, there are a few things that could be the culprit. One possibility is that the gas valve isn’t opening all the way, which is causing a restricted gas flow and not enough to keep the pilot lit. Another possibility is that there’s something wrong with the wiring or connections, which can cause an interruption in the flow of electricity needed to keep the pilot lit.
If you’ve ruled out those possibilities, it’s possible that there’s something wrong with the thermocouple itself. It’s also possible that drafts are causing the pilot light to go out – if your furnace is located near a door or window, try closing it off to see if that makes a difference.
Credit: www.wikihow.com
Kenmore Power Miser 9 Replacement Parts
If your Kenmore Power Miser 9 water heater is in need of replacement parts, there are a few options available to you. The most common replacement parts are the anode rod, heating element, and thermostat. These parts can be purchased at most hardware or home improvement stores.
The anode rod helps to protect the tank from corrosion and can last for several years before it needs to be replaced. The heating element heats the water inside the tank and is the most likely part to fail over time. The thermostat regulates the temperature of the water and should be replaced if it isn’t working properly.
If you need help installing any of these replacement parts, Kenmore offers installation instructions on their website or you can contact customer service for assistance. With a little time and effort, you can keep your Kenmore Power Miser 9 water heater running like new for many years to come!
Kenmore Power Miser 12
5
Kenmore Power Miser 12.5 is a water heater that is specifically designed to be energy efficient. It has a number of features that make it more efficient than other water heaters on the market, including an advanced burner design and an insulation blanket.
Additionally, the Power Miser 12.5 comes with a thermostat that can be set to automatically reduce the water temperature when it is not in use, which further increases its efficiency. Overall, the Kenmore Power Miser 12.5 is an excellent choice for those looking for an energy-efficient water heater.
Kenmore Power Miser 9 Thermostat
If you’re looking for a way to save money on your energy bills, the Kenmore Power Miser 9 Thermostat is a great option. This thermostat is designed to help you reduce your energy consumption by automatically adjusting the temperature of your home based on the outside temperature. The Power Miser 9 also features a vacation mode that allows you to set it to a lower temperature when you’re away from home, so you don’t have to waste energy heating an empty house.
You can even connect it to your smartphone or tablet so you can control it remotely.
The Kenmore Power Miser 9 Thermostat is a great way to save money on your energy bills and keep your home comfortable all year long.
Conclusion
If your Kenmore Power Miser 9 pilot light keeps going out, there are a few things you can try to fix the problem. First, make sure that the gas valve is turned on all the way. If it is, then check to see if the pilot light tube is clogged.
If it is, clean it out with a wire brush and try relighting the pilot light. If that doesn’t work, then you may need to replace the thermocouple.
